| |
USES
A
coating used in the re bottoming and repair of corroded crude oil storage and
ballast tanks. When used as part of a laminating system a badly corroded tank
bottom may be restored to a working condition, which will resist further corrosion
SPECIAL
FEATURES
* SOLVENT FREE
* COST EFFECTIVE
* PREVENTS FURTHER CORROSION
*
RAPID
* FACTORY PRE-WEIGHED COMPONENTS
DESCRIPTION
Araldite
Epoxycoat T.L. is a two component solvent free clear epoxy coating based on
Araldite epoxy resin.
Each component is factory weighed and packaged ready
for on site mixing
PHYSICAL PROPERTIES
| Temperature | 20s
C | 40s
C | | Relative
humidity | 65% | 65% | Pot
life
Re-coating time
Initial hardness
Full cure | 5-7
hours
20-40 hours.
30 hours
days | 2-3
hours
7-15 hours.
12 hours
4 days |
CHEMICAL
PROPERTIES
Samples of Araldite Epoxycoat T.L. were submerged in test reagents
for 12 months at 20s C. The samples were unaffected by the following chemicals:
Sea
water
Sulphuric acid 10%
Sulphuric acid 30 %
Sulphuric acid 70 %
Hydrochloric
acid 10 %
Hydrochloric acid 20 %
Caustic soda 10 %
Caustic soda 30 %
Ammonia
10%
Ammonia 25 %
Acetic acid 10 %
Acetic
acid 50 %
Lactic acid 10 %
Linseed oil fatty acid
Tall oil fatty acid
Xylene
Gasoline
Crude
oil
CAUTION
Keep uncured epoxy
materials away from the mouth, food or drink.
Do not use empty tins to store
food even if they appear to have been cleaned.
Always wear gloves or barrier
cream when handling uncured epoxy materials. Clean any splashes or smears from
the skin immediately using warm water and soap.
Avoid inhaling vapour.
Do
not use below 59 C.
NOTICE
The information in this publication,
given in good faith, is based on the present state of our knowledge but all recommendations
are made without guarantee since the conditions of use are beyond our control.
Buyers and users should make their own assessment of our products under their
own conditions and for their own requirements.
|
KiMYASAL ÖZELLİKLER
Araldite Epoxycoat
T.L. 20° C'de 12 ay sureyle aşağıdaki maddelere daldırılarak test edilmiş ve etkilenmemiştir.
Deniz
suyu
Sülfirik asit % 10
Sülfirik asit % 30
Hidroklorik asit % 10
Hidroklorik
asit % 20
Kostik soda % 10
Kostik soda % 30
Amonyak % 10
Amonyak %
25
Asetik asit % 10
Asetik asit % 50
Laktik asit % 10
Keten
tohumu yağ asidi
Tal yağı asidi
Ksilen
Benzin
Ham petrol
Pürüzlü
beton yüzeylerde sarfiyat daha fazla olacaktır. Kaplama, tam kuruma suresi tamamlanmadan,
kimyevi maddelerle temas etmemelidir.
TEMİZLEME
Vantico Cleaning
Fluid kullanınız.
VERİM
Araldite Epoxycoat T.L.: 10 kg'lık
paketlerde bulunan malzemenin sarfiyatı yaklaşık 1 kg/m2 olacaktır. Pürüzlü yüzeyler
için daha fazla malzeme gerekebilir.
